m (1 revision(s))
Revision as of 13:15, 15 August 2007
This installation is howto connecting with adsl *usb* modem. You should have pardus 1.1alfa2 at least.
Enter to konsole and be root. Then, run the command:
linux onur # adsl-setup Welcome to the Roaring Penguin PPPoE client setup. First, I will run some checks on your system to make sure the PPPoE client is installed properly... Looks good! Now, please enter some information: USER NAME >>> Enter your PPPoE user name (default pardus@ttnet):
Enter your user name to connect.
INTERFACE >>> Enter the Ethernet interface connected to the DSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethn, where 'n' is a number. (default eth0):
Run the command "nas0" (not inverted comma) at this chapter and push the enter button.
INTERFACE >>> Enter the Ethernet interface connected to the DSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethn, where 'n' is a number. (default eth0): nas0
Do you want the link to come up on demand, or stay up continuously? If you want it to come up on demand, enter the idle time in seconds after which the link should be dropped. If you want the link to stay up permanently, enter 'no' (two letters, lower-case.) NOTE: Demand-activated links do not interact well with dynamic IP addresses. You may have some problems with demand-activated links. >>> Enter the demand value (default 0):
Run "no" and push the enter.
DNS Please enter the IP address of your ISP's primary DNS server. If your ISP claims that 'the server will provide DNS addresses', enter 'server' (all lower-case) here. If you just press enter, I will assume you know what you are doing and not modify your DNS setup. >>> Enter the DNS information here:
Don't write anything. Push the enter.
PASSWORD >>> Please enter your PPPoE password: Buraya şifrenizi girin >>> Please re-enter your PPPoE password: Buraya şifrenizin tekrarını girin
Enter your password.
FIREWALLING Please choose the firewall rules to use. Note that these rules are very basic. You are strongly encouraged to use a more sophisticated firewall setup; however, these will provide basic security. If you are running any servers on your machine, you must choose 'NONE' and set up firewalling yourself. Otherwise, the firewall rules will deny access to all standard servers like Web, e-mail, ftp, etc. If you are using SSH, the rules will block outgoing SSH connections which allocate a privileged source port. The firewall choices are: 0 - NONE: This script will not set any firewall rules. You are responsible for ensuring the security of your machine. You are STRONGLY recommended to use some kind of firewall rules. 1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation 2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway for a LAN >>> Choose a type of firewall (0-2):
Choose a type of firewall and push the enter.
** Summary of what you entered ** Ethernet Interface: nas0 User name: pardus@ttnet Activate-on-demand: No DNS: Do not adjust Firewalling: NONE
>>> Accept these settings and adjust configuration files (y/n)?
Run the command "y" and push the enter.
>>> Accept these settings and adjust configuration files (y/n)? y Adjusting /etc/ppp/pppoe.conf Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets (But first backing it up to /etc/ppp/pap-secrets-bak) (But first backing it up to /etc/ppp/chap-secrets-bak)
Congratulations, it should be all set up! ...
In konsole, be root and run this command: br2684ctl -c 0 -b -a 8.35
linux onur # br2684ctl -c 0 -b -a 8.35 br2684ctl: Interface "nas0" created sucessfully br2684ctl: Communicating over ATM 0.8.35, encapsulation: LLC br2684ctl: Interface configured
Connecting to internet
After stand confessed as root, write this:
linux onur # adsl-start . Connected!
If you restart your pc, you must run "br2684ctl -c 0 -b -a 8.35" and "adsl-start" again. If you don't want to write each time, open your local.start file, and add these lines:
br2684ctl -c 0 -b -a 8.35 adsl-start
# /etc/conf.d/local.start # This is a good place to load any misc programs # on startup ( use 1>&2 to hide output) br2684ctl -c 0 -b -a 8.35 adsl-start